Content on this page requires a newer version of Adobe Flash Player.

Get Adobe Flash player

Products: Doors

Download Adobe Reader HERE

Door Specifications:

LS Series - Galvanneal Steel Standard Lock Seam Flush Doors:

1–3/4” thickness fabricated from two sheets of 20, 18, 16 or 14 gauge Galvanneal steel to ASTM A653-B, A40 (ZF120) 0.40 oz/ft2 coating. Optional coating G90 (ZF275) is also available.

Face sheets are premium quality, panel flat tension leveled and flush and free from any seams or joints. Door skins are mechanically interlocked along the vertical hinge and lock edges, designed with a 1/8” in 2” bevel for ease of fit and operation. Doors come standard with high density paper honeycomb core (1” cell size). Optional cores of Polyisocyanurate (R value – 6.5), Polyurethane (R value – 11.1) and Temperature Rise rated for 450 degrees Fahrenheit at 60 minutes all bonded under pressure.

Top and bottom end channels shall be of 16 gauge material projection welded into door. Hardware reinforcements shall be as per recommended minimum gauges as set out by the Canadian Steel Door Manufacturers Association. Hinge reinforcing shall be angled high frequency reinforcements at all locations unless otherwise specified.

Embossed doors - Galvanneal Steel Standard Lock Seam Embossed Doors:

MIN WIDTH = 2’-8”, MAX WIDTH = 3’-6”, MAX HEIGHT – 7’-0”

1-3/4” thickness fabricated from two sheets of 20 or 18 gauge Galvanneal steel to ASTM A653-B, A40 (ZF120) 0.40 oz/ft2 coating.

Face sheets are premium quality, panel flat tension leveled and flush and free from any seams or joints. Door skins are mechanically interlocked along the vertical hinge and lock edges. Designed with a 1/8” in 2” bevel for ease of fit and operation.

Top and bottom end channels shall be of 16 gauge material projection welded into door. Hardware reinforcements shall be as per recommended minimum gauges as set out by the Canadian Steel Door Manufacturers Association. Hinge reinforcing shall be angled high frequency reinforcements at all locations.

HS Series – Galvanneal Steel Stiffened Standard Lock Seam Flush Doors:

1-3/4” thickness fabricated from two sheets of 18, 16 or 14 gauge Galvanneal steel to ASTM A653-B, A40 (ZF120) 0.40 oz/ft2 coating. Optional coating G90 (Z275) is also available.

Face sheets are premium quality, panel flat tension leveled, flush and free from any seams or joints. Door skins are mechanically interlocked along the vertical hinge and lock edges. Optional tack welded and filled and ground smooth to show no visible edge seams. Designed with a 1/8” in 2” bevel for ease of fit and operation. Standard labelled doors shall be internally reinforced with 20 gauge, box shaped steel stiffeners laminated 6” O.C. maximum to both door faces and filled with semi rigid fiberglass insulation. Laminated “Z” stiffeners are used for honeycomb or styrene core doors. “Interlocking” stiffeners are also available spot welded to both faces approximately 6” O.C. and filled with semi rigid fiberglass insulation. Top and bottom end channels shall be of 16 gauge material projection welded into door. Hardware reinforcements shall be as per recommended minimum gauges as set out by the Canadian Steel Door Manufacturers Association. Hinge reinforcing shall be angled high frequency reinforcements at all locations.

Note as per CSDMA – 2006 [08100]: “Spot welding leaves small marks on the face of welded stiffener construction doors which may be visible after the application of finish paint. Their removal is difficult and may be impractical. These are inherent in the product and are not to be considered as manufacturing defects. The use of translucent paints, paints with a gloss rating greater than 20% when measured with a 60 degree gloss meter, or dark colours, are not recommended. Where aesthetics are seen as a more critical issue, the Specifier should consider utilizing laminated core construction.”

WS Series Door – Steel Stiffened Continuously Welded Seam Flush Doors:

1-3/4” thickness fabricated from two sheets of 16 or 14 gauge Galvanneal steel to ASTM A653-B, A40 (ZF120) 0.40 oz/ft2 coating. Optional coating G90 (Z275) is also available.

Face sheets are premium quality, panel flat tension leveled, flush and free from any seams or joints. Door seams are continuously welded lap seams filled and ground smooth to show no visible edge seams, designed with a 1/8” in 2” bevel for ease of fit and operation. Doors shall be internally reinforced with 20 gauge interlocking steel stiffeners spot welded 6” O.C. maximum to both door faces. Doors come standard with semi rigid fiberglass insulation. Top and bottom end channels shall be of 16 gauge material projection welded into door. Hardware reinforcements shall be as per recommended minimum gauges as set out by the Canadian Steel Door Manufacturers Association. Hinge reinforcing shall be 10 GA. angled high frequency reinforcements at all locations.

Note as per CSDMA – 2006 [08100]: “Spot welding leaves small marks on the face of welded stiffener construction doors which may be visible after the application of finish paint. Their removal is difficult and may be impractical. These are inherent in the product and are not to be considered as manufacturing defects. The use of translucent paints, paints with a gloss rating greater than 20% when measured with a 60 degree gloss meter, or dark colours, are not recommended. Where aesthetics are seen as a more critical issue, the Specifier should consider utilizing laminated core construction.”

SSD Series - Stainless Steel Doors:

1–3/4” thickness fabricated from two sheets of 20, 18, or 16 gauge Stainless Steel Type 304 XL Blend “S”, or 316 Blends "S", available with lite cut-outs as required.

Face sheets are premium quality, panel flat tension leveled, flush and free from any seams or joints. Door skins are mechanically interlocked along the vertical hinge and lock edges, designed with a 1/8” in 2” bevel for ease of fit and operation. Doors come standard with high density paper honeycomb core (1” cell size). Optional cores of Polystyrene (R value – 6.5), Polyisocyanurate (R value – 11.1). Top and bottom end channels shall be of 16 gauge material projection welded into door. Hardware reinforcements shall be as per recommended minimum gauges as set out by the Canadian Steel Door Manufacturers Association. Hinge reinforcing shall be angled 10 GA. high frequency reinforcements at all locations unless otherwise specified.

Hardware Preparations:

Doors shall be blanked, reinforced, drilled and tapped for mortised template hardware. Holes 1/2” diameter and larger shall be factory prepared, except mounting and through bolt holes, which are by others, on site, at the time of hardware installation. Holes less than ½” diameter shall be factory prepared only when required for the function of the device (for knob lever cylinder, thumb or turn pieces) or when these holes overlap function holes. Doors shall be reinforced, where required, for surface mounted hardware. Drilling and tapping for pivots, holders and other such items will be done by others in the field, at the time of installation.

Hardware Locations:

Unless specified otherwise, the location of hinges, locks, exit devices, push / pull plates, closers etc. shall be as per All Steel Doors 2000 standard locations.

Fire Rated Doors:

Fire labelled doors shall be provided for those openings requiring fire protection ratings, as determined and scheduled by the architect. Such products have been tested in strict conformance with CAN4 –S105, ASTM E – 152 or NFPA 252 as listed by a nationally recognized agency having a factory inspection service and shall be constructed as detailed in the follow – up service procedures.

Glazing:

Doors shall be supplied with formed glazing strips complete with Snap-in stops to accommodate ¼: (6 mm) glass supplied and installed by others.

Site Storage and Protection:

All doors shall be thoroughly inspected upon receipt and all discrepancies, deficiencies and/or damages shall be reported, in writing to All Steel Doors 2000 within 3 days of receipt of shipment. All shipments are FOB All Steel Doors 2000. All damages incurred during shipment to be claimed by the distributor directly to the freight carrier. Doors shall be removed from any wrapping or covering and be stored in a protected location in an upright position, on wood sills spaced with blocking to permit air circulation.

Installation of Doors:

Install doors and hardware in accordance with hardware templates and manufacturers instructions. Adjust operable parts for correct clearances and functions.

Warranty:

All doors shall be guaranteed to be free of defects in material and workmanship for one year. There are no warranties expressed or implied, which extend beyond those described herein:

If product is found to be defective, we will at our discretion either repair or replace the defective item(s). All Steel Doors 2000 Ltd. will not be liable or obligated for any damages of any kind beyond this repair or replacement. Misuse, abuse, improper storage and/or handling, improper installation or application of product will not be covered by warranty at our discretion. Our warranty terminates one year after product has been shipped from our plant and at any time anyone other than an individual authorized by us performs any work or repair, service or replacement of the product without prior written approval.

Back to Top
Back to Top

Website Design by iRISEmedia.com | Toronto SEO Company